Photo Gallery (12 photos)

$7,090.00

Call for package pricing and discounts on multiple units! Industry`s ONLY Non-Carboning Oil Preheater block with Solid State circuit board controller. These items precisely control the oil and air temperatures to insure stable viscosity for optimum control of the flame resulting in a thorough burn. Heater block never carbons or needs to be removed for cleaning. Industry normal annual parts kit not needed with Omni`s system! Readjustment of electrodes and nozzle replacement every 5 years is all that is needed due to erosion only.

Omni is the only waste oil burner manufacturer who can say without equivocation it`s oil preheater block absolutely will not carbon the oil internally due to its patented design. Therefore, the industry normal removal of carbon in the preheater block is not necessary. This design ensures that OMNI customers will never need to remove the burner for periodic carbon cleaning!

There are many who have easy access to their oil preheater block, but cleaning the hard lava-like carbon is not an easy task! Others request the entire burner be serviced at least annually. Part of that service is flushing their oil preheater block of carbon buildup. Some must do this more than others, as frequently as twice a season.

Fully cleaning and removing carbon is a difficult chore. Even after cleaning, carbon chunk particles can remain. Shortly after service, they can plug the oil nozzle, shutting the unit down. This causes a lot of down time and repeat service, not experienced with OMNI units.

• Omni's Patented Flame Control System - Designed and constructed waste oil burning equipment that reached a level of performance the industry considers unattainable!
  • System Benefits
    • Non-carboning oil heater block - cleaning not required
    • A thorough burn - greatly reducing ash deposit accumulation
    • Only system on metals -can't overfire. No target burn-out
    • Clean heater once a season under normal conditions
    • The most reliable, consistent operation
    • Greater efficiency

  • Variably controlled, A/C converted, D/C gear motor driven waste oil pump
    • Oil Primer Switch
    • Inline breaker
    • Oil Pressure Gauge - Bench mark indicator for proper flame length adjustment and filter pump screen or valve cleaning requirements
    • Cleanable Strainer Oil Filter - removal of one nut for screen access
    • Oil Shut-Off Valve - eliminates start delays due to possible drain back
    • Adjustable Motor Speed - initial set-up only - once set, no adjustment needed thereafter

  • Patented Oil Preheater & Controller
    • Continues the stabilization of the waste oil viscosity by holding oil and air temperatures that pass through it exact. Resulting in the most thorough and complete burn. OIL HEATER BLOCK WILL NOT BUILD UP CARBON INSIDE ITS OIL PASSAGES!

  • Crimped Heat Exchangers
    • The seam construction eliminates the possibility of stress cracks when welded due to a heat effected zone. This can occur if overheated when flue gas passages may become blocked if not cleaned periodically or insufficient draft was present caused by inaccurate installation.

  • Easy Maintenance When Needed
    • Large lift out cabinet door (150/250/350/500 models) and a hinged end plate cover opening (250/350/500 models) makes for easy access to combustion chamber & heater exchangers for occasional vacuuming of ash deposit accumulation. Under normal operating conditions, seasonal cleaning is required. Some oils require only once a year cleaning. Swing out burner door, no fuel or air lines to disconnect. Removal of one nut and electrical safety plug allows easy access to flame end cone and nozzle for quick service. Our on-burner air compressor eliminates overnight risk to your shop compressor. Hinged Cover opening provides quick access to heater block and circuit board if needed.

  • Heater Specifications
    • BTU/HR Input : 350,000
    • BTU/HR Output : 300,000
    • Gallons per Hour : 2.4
    • Voltage Rquirements : 115V
    • Amps, Full Load : 16.6
    • Fan Motor HP : 2@1/4 each
    • Fan Motor RPM : 1,075
    • Fan Diameter/Pitch : 18/36
    • CFM (Free Air) : 6,275
    • CFM w/ Ductwork : 1600
    • Effective Air Flow : 70 ft.
    • Flue Size : 8"
    • Weight with Burner : 565 lbs.
    • Shipping Weight : 600 lbs.
    • Dimensions (LxWxH) : 54" x 29.5" x 28.5"
    • Shipping Dimensions : 76" x 38" x 49"

  • Econo Heat designed and constructed waste oil burning equipment that reached a level of performance the industry considers unattainable!